The wall form­work that needs up to 50% few­er ties

The all-in-one wall form­work sys­tem that's quick and easy to han­dle

Dokaset is a fast, cost-sav­ing wall form­work sys­tem for the build­ing con­struc­tion seg­ment. All op­er­a­tions such as at­tach­ing the lift­ing chain and plac­ing the form-ties can be car­ried out very quick­ly and eas­i­ly from ground lev­el. Ful­ly pre-mount­ed work­ing plat­forms, the rev­o­lu­tio­nary Xlife form­work sheet and wide tie spac­ing are among the prac­ti­cal fea­tures that set this all-in-one sys­tem apart.

The fast form­work sys­tem for walls

will speed up work at your site

The ad­van­tages are plain to see…

  • up to 50% few­er wall-ties than con­ven­tio­n­al framed form­work

  • short­er form­ing-times, as the form­work can be tied work­ing from one side on­ly

  • ready for use in a few sim­ple steps

Su­perla­tive safe­ty dur­ing form­ing and pour­ing

en­sures fast work­ing and safe work­site con­di­tions

Er­go­nom­ic, safe work­ing be­cause

  • the crew can place the form-ties and at­tach the lift­ing chain work­ing from ground lev­el

  • lad­ders, work­ing plat­forms and rail­ings are all in­te­grat­ed in the sys­tem

High­ly eco­nom­i­cal

as it is easy to op­er­ate and ex­treme­ly durable

Ide­al for many re-use cy­cles, thanks to

  • the small num­ber of form-ties, that are quick and easy to op­er­ate

  • steel frames that are hot-dip gal­vanised both in­side and out

  • the long-life, easy-to-clean Xlife sheet

  • the wide­ly spaced form-ties, for short form­ing-times

The ul­ti­mate in flex­i­bil­i­ty

for per­fect adapt­a­bil­i­ty to any on-site si­t­u­a­tion

Ver­satile ap­pli­ca­tio­n­al range, as

  • it can eas­i­ly be com­bined with Fra­max Xlife and Alu-Fra­max Xlife

  • it can be ver­ti­cal­ly stacked very quick­ly, us­ing pan­els from the Fra­max Xlife "con­struc­tion kit"

  • the sys­tem fea­tures an in­te­grat­ed corn­er so­lu­tion that does not need any ex­tra ties

Dokaset

  • Rugged large-area panels, meaning a very low form-tie ratio
  • Integral platforms and ladders, providing exceptionally high workplace safety
  • Sturdy steel frames, galvanised both inside and out, for flat, plane concrete faces
  • Stacking elements from the Framax Xlife "construction kit" permit formwork heights of up to 412 cm

Fra­max Xlife sheet

  • Extremely high numbers of re-use cycles with superlative concreting results, for unparalleled cost efficiency and fewer changes of form-facing
  • No burst-off plywood chips, and less water absorbed through nail-holes, for longer service life
  • Special surface structure for less touching-up and reduced close-out costs
  • Timber-plastic composite sheet that can also be cleaned using a high-pressure washer

Not many form-ties, and quick to op­er­ate

Pressure ties at the top edge automatically keep the formwork-halves the right distance apart. These form-ties do not need to be operated. The tension ties can be operated from one side of the formwork, which is ergonomically convenient and saves a lot of time.

Su­perla­tive safe­ty dur­ing form­ing and pour­ing

The access route to the working platform is safeguarded thoroughly and well. An integrable ladder enables the crew to climb up and down quickly and safely. With its rear and side guard rails, the working platform provides all-round protection during pouring.

Wide form-tie spac­ing

Wide spacing between the form-ties means fewer form-tie points. This saves on equipment, labour and costs, making for maximum efficiency.

Safe lift­ing and re­sett­ing

The lifting chain can be reached from ground level – for the greatest workplace safety.

The Dokaset F sys­tem

Dokaset F has been optimised for the special requirements of the French market. It comes with integrated safety accessories, is ready for immediate use and can easily be combined with Framax Xlife. Together with the non-rusting Framax Xlife sheet, this "all-in" formwork system ensures good concrete surfaces and is very service-friendly and durable.

Safe lad­der­ways

The access route to the working platform is safeguarded thoroughly and well. Integrated ladders and flap-type openings in the platform decking enable the crew to climb up and down quickly and safely.

Safe work­ing plat­forms

The working platform is fitted with rear and side guard rails as standard. The all-round protection is complemented by a pull-out opposing guard-rail.

Ready-as­sem­bled

On Dokaset F, all the safety accessories (platform, guard rails, ladderway, panel struts) are already mounted ready for immediate on-site deployment.

Fra­max Xlife sheet

The Framax Xlife sheet does not cause any rust-spots, and ensures clean concrete faces.

For the ul­ti­mate in work­place safe­ty

Dokaset F meets the stringent safety requirements of the French market.