Framed formwork Frami eco
The economical hand-set and crane-lifted formwork system for walls, columns and foundations
Highly cost-efficient
thanks to its optimised product qualityLong formwork-system lifespan, achieved by
- high-grade formwork sheeting
- specially coated hollow-section steel frames
- sturdy system components
High strength and load capacity
thanks to rugged yet light constructional designFrami eco is sturdy enough for the crane and light enough to be set by hand, and
- reduces the number of connector components
- lowers close-out and rehabilitation costs
- makes it possible to form faster, as there are fewer form-ties
Speeds up the construction workflow
by shortening the forming-timesFaster working, thanks to
- simple system-grid with fewer panels
- low form-tie ratio
- small number of connectors
- minimised infill zones
- reduced commissioning quantities
Comprehensive workplace safety
with compatible ladderways and working platforms- safe vertical access with the Ladder system XS
- workplace safety on all sides with the Frami pouring platform
- practical accessories – such as panel struts, lifting hook etc. – make for safe, easy handling of the formwork
References
System
Simple system-grid
- widths from 30 cm to 90 cm in 15-cm increment grids for best-possible adaptation to the structure
- practical heights of 1.20 and 3.00 m
- 75 cm wide universal panel for outside corners, columns and end-shuttering
- larger gang-forms for fast repositioning with crane possible
Frami clamp
- one blow of the hammer on the Frami clamp is all it takes to pull the panels together and achieve a flush, correctly aligned panel joint that is resistant to tensile forces
- no need for extra stiffening reinforcements
Continuous height mismatch
- continuous hardware slot in the frame for fixing the Frami clamp anywhere on the frame
- continuous height mismatch without pre-defined increment-grid
- easy accommodation to steps, slopes and uneven ground, without extra work
Utilisation
In use across the entire room height
- only three form ties per 300 cm panel height
- permitted fresh-concrete pressure: 60 kN/m²
- cost-effective forming of stop-ends, outer corners and columns through special hole pattern in the 75 cm wide Frami eco universal panel
- an extensive range of accessories ensures safety when pouring
Used for foundations
- the Frami tie-holder bracket relocates the form tie above the panel (form tie not in concrete) for flexible positioning
- foundation anchoring system consisting of flat tie rods and Frami clips
- for walls between 10 cm and 80 cm thick in a 5-cm increment-grid
- no anchoring through concrete
- no supporting timbers required
- the bottom of the panel is fixed with foundation clamps and perforated tape
Suitable products
Instruction documents/web pages further languages
Framed formwork Frami Xlife / Frami eco
User Information booklet (en)Rahmenschalung Frami Xlife / Frami eco
User Information booklet (de)Encofrado marco Frami Xlife / Frami eco
User Information booklet (es)Fôrma modulada Frami Xlife / Frami eco
User Information booklet (pt)Рамная опалубка Frami Xlife / Frami eco
User Information booklet (ru)Рамна опалубка Frami Xlife / Frami eco
User Information booklet (ua)Lifting of framed formwork
Short instruction (en)Lifting of framed formwork
Short instruction (en)Order of closing and stripping out the framed formwork with Platform system Xsafe plus
Short instruction (en)Safe construction - Pouring platform U
Short instruction (en)Reihenfolge Ein- und Ausschalen von Rahmenschalungen mit Bühnensystem Xsafe plus
Short instruction (de)Sicherer Aufbau - Betonierbühne U
Short instruction (de)Umsetzen von Rahmenschalungen
Short instruction (de)Les differentes étapes du coffrage et décoffrage d'un coffrage cadre avec Xsafe plus
Short instruction (fr)Translation d'un coffrage cadre
Short instruction (fr)Ordine di armo de siarmo casseratura e telaio con Sistema di passerelle Xsafe plus
Short instruction (it)Traslazione casseratura a telaio
Short instruction (it)
