Framed formwork Alu-Framax Xlife

The lightweight alu­mini­um framed formwork for forming with or with­out a crane

With its low weight, Alu-Framax Xlife brings all the ben­e­fits of Framax Xlife framed formwork to crane­less job­sites as well – al­so seam­less­ly com­bined with Framax Xlife, of course.


Lightweight and ver­satile
thanks to stur­dy alu­mini­um pro­file frame 

  • the low pan­el weight re­duces the work-strain as­so­ci­at­ed with hand-set forming, yet the pan­els have a high load ca­pac­i­ty of 60 kN/m²
  • the frames are made of tor­sion-proof hol­low alu­mini­um pro­files, so can al­so be shift­ed by crane
  • seam­less tran­si­tion­ing to Framax Xlife makes op­er­a­tions easi­er to break down in­to crane-han­dled and man-han­dled zones, per­mitt­ing flex­i­ble lo­gis­tics and fast work­flow on the site

be­cause of its out­s­tand­ing sys­tem at­tributes 

  • high num­bers of re­peat us­es made pos­si­ble by its ex­cel­lent man­u­fac­tur­ing qual­i­ty and ex­tra-durable Xlife-sheet
  • high load ca­pac­i­ty thanks to top-qual­i­ty forged con­nec­tor components
  • small­er num­ber of (ex­pen­sive) clo­sure zones, due to the con­sis­tent 15 cm in­cre­ment grid
  • us­ing the sin­gle-side-op­er­able ty­ing sys­tem Monotec op­ti­mis­es work­flows in confined spaces as well

Easy han­dling and plan­n­ing
thanks to prac­ti­cal pan­el size-grid 

  • the in­ge­nious­ly co-or­d­i­nat­ed pan­el for­mats, with their log­i­cal size-grid, help you make op­ti­mum use of formwork com­mis­sion­ing quan­ti­ties
  • uu­ni­ver­sal pan­els, for prac­ti­cal corn­er con­fig­u­ra­tions and col­umn form­works
  • top-qual­i­ty trans­par­ent pow­der-coat­ing makes for easy clean­ing and uni­form frame ap­pear­ance, even af­ter many re­peat us­es
  • fast, easy plan­n­ing with the Ti­pos plan­n­ing soft­ware

Su­perla­tive con­crete re­sults
fa­cil­i­tat­ed by prac­ti­cal prod­uct de­tails 

  • clean con­crete fin­ish from the high-grade Xlife sheet with its plas­tic-en­hanced sur­face
  • the in­ge­nious­ly co-or­d­i­nat­ed pan­el for­mats per­mit a neat joint pat­tern even when com­bin­ing up­right and hor­i­zon­tal pan­els
  • no screw im­prints in the con­crete, as the formwork sheet is screwed on from the rear
  • the neat neg­a­tive frame-im­prints in the con­crete min­imise any fin­ish­ing-work

Com­pre­hen­sive work­place safe­ty
with com­pat­i­ble lad­der­ways and work­ing plat­forms 

  • safe ver­ti­cal ac­cess with the Lad­der sys­tem XS
  • work­place safe­ty on all sides with the Platform sys­tem Xsafe plus
  • prac­ti­cal accessories – such as pan­el struts, lift­ing/re­po­si­tion­ing de­vices, 3-in-1 pole tool etc. – make for safe, easy han­dling of the formwork



Alu-Framax Xlife

  • ingeniously co-ordinated panel formats, for getting maximum utilisation from the formwork
  • 15 cm grid, achieved with only five widths and two heights, simplifies planning, forming and logistics on the site
  • the high-grade powder-coating on the Alu-Framax Xlife panels reliably prevents concrete adhesion
  • integrated waling system: the connection profiles make it easy to attach accessories – with no obligatory fixing points

Framax Xlife sheet

  • very high numbers of re-use cycles possible, thanks to plastic-enhanced surface and special sheet structure
  • fewer positive imprints, due to the sheet's great resistance to scratching and vibrator damage
  • fewer areas needing repair, as there is no splintering and far less swelling around nail-holes
  • easy, fast (intermediate) cleaning, also using high-pressure washer

Alu-Framax pallets

The practical Alu-Framax pallets make light work of offloading the panels at the site.

Framax cir­cu­lar forming plate

By combining Framax circular forming plates and Alu-Framax Xlife panels, it is possible to form polygonal curves.

Com­bin­ing with Framax Xlife

Combining Framax Xlife with Alu-Framax Xlife makes it possible to divide up the site into crane-handled and man-handled zones, making for flexible logistics and a fast workflow on the site.

Uni­ver­sal pan­el

The 75 cm wide Alu-Framax Xlife universal panel is used for forming columns, stop-ends and corners.

Suitable products