Solutions for your construction projects

Doka offers formwork solutions for all areas of construction activity – for anything from housing developments to transportation infrastructure and power-generation facilities, or for building the world’s tallest structures. You can choose from formwork systems and components for any construction project and any requirement.

Filter Formwork and Services
  • Framed formwork Framax Xlife

    Framed formwork Framax Xlife

    Wall Formwork

    Framax Xlife is the framed formwork sys­tem that us­es on­ly a very few dif­fer­ent pan­el for­mats to achieve a con­sis­tent 15 cm in­cre­ment-grid, no mat­ter whether the pan­els are stood up­right or on their sides. All the con­nec­tors and accessories fit seam­less­ly in­to this grid – mak­ing for fast forming-times and high ef­fi­cien­cy.

  • Panel floor formwork Dokadek 30

    Panel floor formwork Dokadek 30

    Floor Formwork

    Dokadek 30 is a beam-less, hand-set formwork sys­tem de­signed as a lightweight steel struc­ture with yel­low coat­ed frames faced with timber/plas­tic-composite sheet­ing. Dokadek 30 com­bines the ad­van­tages of a pan­el floor formwork sys­tem with those of Dokaflex floor-slab formwork: its 3 m² large pan­els make it fast in typ­i­cal zones, yet – thanks to Dokaflex – it is quick and flex­i­ble in the in­fill zones as well. Dokadek 30 – with or with­out drop head: the evo­lu­tion of floor-slab formwork.

  • Formwork beams

    Formwork beams

    System Components

    Doka timber formwork beams are the ba­sis for many Doka formwork sys­tems and have a wide range of us­es. Hun­dreds of thou­sands of th­ese care­ful­ly man­u­fac­tured beams do ster­ling ser­vice on count­less con­struc­tion sites ev­ery day. The H20 ­top and H20 e­co beams are fa­miliar names all over the world, and are the right choice for any ap­pli­ca­tion.

  • Framed formwork Frami Xlife

    Framed formwork Frami Xlife

    Wall Formwork

    The lightweight Frami Xlife formwork, with its stur­dy hot-dip gal­vanised steel frame, is ide­al for fast and eco­nom­i­cal forming, with or with­out a crane.

  • Floor props

    Floor props

    System Components

    Doka floor props are the right choice for ev­ery us­age si­t­u­a­tion, and a stur­dy 'sup­port' in the rough-and-tum­ble of ev­ery­day work on the site. The an­ti-hand­trap and an­ti-dropout safe­guard, forged nut, gal­vanised fin­ish and er­go­nom­i­cal­ly shaped fas­ten­ing clamp are just a few of the fea­tures of th­ese pre­mi­um tubu­lar steel props that have con­vinced cus­tomers all over the world.

  • Concremote - realtime concrete intelligence

    Concremote - realtime concrete intelligence

    System Components

    Concremote uses sensors to measure concrete temperature and calculate strength development in the concrete element. In this way it is possible to determine the best possible concrete mixture and the earliest possible stripping time. Data from Concremote allows for a significantly faster building progress and in doing so supports you in implementing your projects in a cost-efficient way.

  • Platform SCP

    Platform SCP

    Climbing Formwork

    The Platform SCP has room for all the site equip­ment need­ed, and is ful­ly en­closed for safe, weather-shield­ed work­ing, even at great heights. Pow­er­ful hy­draulic cylin­ders crane­less­ly raise the platform, formwork, equip­ment containers and con­crete plac­ing boom to the next cast­ing sec­tion, in on­ly one lift.

  • Large-area formwork Top 50

    Large-area formwork Top 50

    Wall Formwork

    Large-area formwork Top 50 is a 'con­struc­tion kit' large-area formwork sys­tem that is pre-as­sem­bled on a pro­ject-spe­cif­ic ba­sis and is de­signed to ac­com­plish many very di­verse types of task. The shape, size, tie-hole pat­tern and form-fac­ing of the el­e­ments can be adapt­ed to suit any re­quire­ment.

  • Framed formwork Framax Xlife plus

    Framed formwork Framax Xlife plus

    Wall Formwork

    The cen­tre­piece of the new Framed formwork Framax Xlife plus is the Framax Xlife plus form tie. It can be op­er­at­ed from one side and saves up to one third in forming and strip­ping time. Due to its con­i­cal shape, there is no need for jack­et tubes and cones. In­no­va­tive: Form-tie sleeves are com­plete­ly sealed with­out wear­ing parts.

  • Dokamatic table

    Dokamatic table

    Floor Formwork

    The in­no­va­tive­ly de­signed Dokamatic table is the fast way to form large ar­eas of slab. The sys­tem is op­ti­mised to give short forming-times, and copes well with vary­ing struc­tu­ral-de­sign and ge­o­met­ri­cal re­quire­ments. Save on man­hours and crane time: with the 'DoKart plus', the ta­bles can eas­i­ly be trav­elled to their next lo­ca­tion by just one man work­ing on his own.

  • DFDS Formwork Planning

    DFDS Formwork Planning


    Exact planning is the basis for fast and safe forming operations. Now you can make planning easy as a breeze with Doka Formwork Design Software 9, the professional tool for optimal formwork planning on the site. Included: Tipos 9, DokaCAD9 for AutoCAD, Piece list Editor 9 and Beam Statics 9.

  • Protection screen Xclimb 60

    Protection screen Xclimb 60

    Safety Systems

    The Pro­tection screen Xclimb 60 lets you car­ry out con­struc­tion work in the top build­ing-lev­els of high-rise pro­jects in great safe­ty, and pro­tect­ed from the weather. Pro­tection screen Xclimb 60 is a hy­drauli­cal­ly climbed sys­tem that can al­so be quick­ly re­po­si­tioned by crane if suf­fi­cient craneage is avai­l­able. Be­cause it is struc­ture-guid­ed at all times, it can be op­er­at­ed even in windy con­di­tions. The sys­tem comes in sev­er­al ver­sions, giv­ing you the ide­al so­lu­tion for ev­ery re­quire­ment.

  • myDoka customer portal

    myDoka customer portal


    First-class digital customer service. The portal myDoka offers our clients 24/7 access to project and site-specific data – from the comfort of your PC or tablet. myDoka is convincing with its ease of handling, security of confidential data and opens up an ideal interface with the Doka team.

  • Load-bearing tower Staxo 100

    Load-bearing tower Staxo 100

    Load-bearing Systems

    With its rugged steel frames, Staxo 100 is de­signed for large shoring-heights and high loads. It unites high load ca­pac­i­ty and safe­ty, in ev­ery si­t­u­a­tion.

  • Wall formwork FF20

    Wall formwork FF20

    Wall Formwork

    With its prac­ti­cal el­e­ment size-grid, rapid stack­a­bil­i­ty and slip­page-free in­ter-el­e­ment con­nec­tions, FF20 is the right choice for many pro­jects where stric­ter re­quire­ments are made re­gard­ing the con­crete fin­ish.

  • Climbing formwork MF240

    Climbing formwork MF240

    Climbing Formwork

    Climbing formwork MF240 per­mits con­trolled, reg­u­lar work­ing cy­cles on all struc­tures. The sys­tem is sim­ple to op­er­ate, han­dles wall in­cli­na­tions of up to 15 de­grees and can be di­men­sioned to many dif­fer­ent re­quire­ments over a wide range of ap­pli­ca­tions.

  • Supporting construction frame

    Supporting construction frame

    Wall Formwork

    'Sup­port­ing con­struc­tion frames' en­able the con­cret­ing forces to be safe­ly trans­ferred by way of di­ag­o­n­al an­chors in cas­es where it is not pos­si­ble to tie wall-formwork el­e­ments through the con­crete.

  • Circular formwork H20

    Circular formwork H20

    Wall Formwork

    Cir­cu­lar formwork H20 is a prac­ti­cal cir­cu­lar formwork sys­tem that de­liv­ers smooth, curved walls from radii of 3.50 m up­ward – ste­p­less­ly.

  • Rental service

    Rental service


  • Edge protection system XP

    Edge protection system XP

    Safety Systems

    This sys­tem is the uni­ver­sal safe­ty so­lu­tion for all edge pro­tection needs. It fits in ide­al­ly with Doka sys­tems – be they wall or floor-slab formwork – for safe­guard­ing slab-edges or as fall-ar­rest bar­ri­ers on the struc­ture shell.

  • Plumbing accessories

    Plumbing accessories

    System Components

    Doka pan­el struts and plumb­ing struts wind­proof the formwork and make it easi­er to plumb and align. The mo­d­u­lar com­bi­na­tion of plumb­ing struts, prop heads and prop shoes makes for op­ti­mum us­a­bil­i­ty with Doka formwork sys­tems.

  • Framed formwork Alu-Framax Xlife

    Framed formwork Alu-Framax Xlife

    Wall Formwork

    With its low weight, Alu-Framax Xlife brings all the ben­e­fits of Framax Xlife framed formwork to crane­less job­sites as well – al­so seam­less­ly com­bined with Framax Xlife, of course.

  • Dokaflex


    Floor Formwork

    Dokaflex is the timber-beam floor formwork for all kinds of lay­outs. Meet­ing in­di­vi­d­u­al re­quire­ments re­gard­ing the con­crete fin­ish is no problem, as any type of form-fac­ing can be cho­sen. Two Dokaflex de­sign ver­sions are avai­l­able for use to meet your pro­ject re­quire­ments.

  • 3-ply sheets, formwork sheets

    3-ply sheets, formwork sheets

    System Components

    Doka 3-SO three-ply sheets pro­vide the ba­sis for many Doka formwork sys­tems and have a wide range of us­es.

  • Multi-ply formwork sheets

    Multi-ply formwork sheets

    System Components

    Doka mul­ti-ply formwork sheets are used in very many Doka formwork sys­tems. The broad spec­trum – rang­ing from Doka­P­ly to the Xlife sheet – al­lows Doka to of­fer ide­al so­lu­tions for many dif­fer­ent re­quire­ments and cater for any­thing from in­fill zones to fair-faced con­crete.

  • Automatic climbing formwork Xclimb 60

    Automatic climbing formwork Xclimb 60

    Climbing Formwork

    Au­to­mat­ic climbing formwork Xclim­b 60 is a hy­drauli­cal­ly climbed sys­tem that can al­so be quick­ly raised by crane if suf­fi­cient craneage is avai­l­able. Be­cause it is guid­ed on the struc­ture at all times, the sys­tem can still be climbed even in windy con­di­tions.

  • Shifting devices for tables

    Shifting devices for tables

    Floor Formwork

    With Doka shift­ing de­vices, slab-forming op­er­a­tions can be ac­com­plished even faster. By mak­ing the crane un­ne­ces­sary for both the hor­i­zon­tal and ver­ti­cal re­po­si­tion­ing op­er­a­tions, they sim­pli­fy and op­ti­mise the lo­gis­tics for the en­tire site, by do­ing away with un­pro­duc­tive (mean­ing cost­ly) wait­ing times. The craneage saved here is then avai­l­able for use else­where. This ac­cel­er­ates the en­tire site work­flow, sav­ing on labour costs and boost­ing the con­trac­tors' com­pet­i­tive­ness.

  • Working scaffold Modul

    Working scaffold Modul

    Safety Systems

    The Work­ing scaf­fold Mo­d­ul is the ide­al add-on to Doka wall sys­tems: with this rentable mo­d­u­lar platform sys­tem, re­in­force­ment op­er­a­tions can be car­ried out safe­ly and quick­ly. It is equal­ly suit­able for use as a stair tow­er or a mo­bile scaf­fold tow­er. To speed up the con­struc­tion work­flow still fur­ther, the platform units can be re­po­si­tioned by crane.

  • Dokaflex table

    Dokaflex table

    Floor Formwork

    Dokaflex ta­bles are easy and prac­ti­cal to set up and can be shift­ed and adapt­ed very quick­ly. This makes them a cost-ef­fec­tive and ef­fi­cient way of car­ry­ing out large-area slab pro­jects. Dokaflex ta­bles can of course be com­bined with Dokamatic ta­bles.

  • Release-agents


    System Components

    Doka of­fers re­lease-agents for both smooth and ab­sor­bent formwork sur­faces. They have an ex­cel­lent se­parat­ing ef­fect and make for at­trac­tive con­crete sur­faces.

  • Multi-trip packaging

    Multi-trip packaging

    System Components

    Mul­ti-trip pack­ag­ing items such as containers, stack­ing pallets and skele­ton tran­s­port box­es keep ev­ery­thing neat and tidy on the site, min­imise the time wast­ed search­ing for parts and stream­line the stor­age and tran­s­port of sys­tem components, small items and accessories. The stack­ing pallets sim­pli­fy the stor­age and han­dling of floor props, folding tripods, formwork beams and sheets. The skele­ton tran­s­port box is the tidy way of stor­ing and han­dling lighter accessories (max. load 700 kg). For heavi­er accessories, there is plen­ty of space for th­ese in the Mul­ti-trip tran­s­port box (max. load 1500 kg).

  • Form ties/Suspension cones

    Form ties/Suspension cones

    System Components

    De­pend­able form-ties and safe sus­pen­sion points are cru­cial for ef­fi­cient and safe us­age of any formwork. For both wall formwork, sin­gle-sid­ed formwork and climbing formwork, a com­plete range of field-proven form-tie so­lu­tions and sus­pen­sion points is avai­l­able.

  • Aluminium formwork beams

    Aluminium formwork beams

    System Components

    The in­no­va­tive cross-sec­tion of the Alu box beam gives it a high load rat­ing, per­mitt­ing op­ti­mised equip­ment us­age on the site. The in­te­grat­ed nail­ing strip and the end-to-end fix­ing slot en­able the beam to be re-used in­ten­sive­ly, and give it a long lifes­pan.

  • Facade formwork Top 50

    Facade formwork Top 50

    Wall Formwork

    Fa­cade formwork Top 50 speeds up work on pre-cast fa­cades, both with in­te­grat­ed and set-back CIP columns.

  • Dokaset


    Wall Formwork

    Dokaset is a fast, cost-sav­ing wall formwork sys­tem for the build­ing con­struc­tion seg­ment. All op­er­a­tions such as at­tach­ing the lift­ing chain and plac­ing the form-ties can be car­ried out very quick­ly and eas­i­ly from ground lev­el. Ful­ly pre-mount­ed work­ing plat­forms, the Xlife formwork sheet and wide tie spac­ing are among the prac­ti­cal fea­tures that set this all-in-one sys­tem apart.

  • Column formwork Top 50

    Column formwork Top 50

    Wall Formwork

    Com­pli­cat­ed col­umn cross-sec­tions, large col­umn heights, many formwork re-use cy­cles, tough spe­c­i­fi­ca­tions re­gard­ing the con­crete fin­ish – a made-to-mea­sure Col­umn formwork Top 50 can han­dle them all eco­nom­i­cal­ly.

  • Column formwork RS

    Column formwork RS

    Wall Formwork

    Ex­act­ly round columns, in su­perla­tive fair-faced con­crete qual­i­ty, can be achieved us­ing Col­umn formwork RS.

  • Column formwork KS Xlife

    Column formwork KS Xlife

    Wall Formwork

    For si­t­u­a­tions where large num­bers of square and rec­tan­gu­lar columns, with vari­able cross-sec­tions, need to be formed cost-ef­fec­tive­ly and on sche­d­ule.

  • Column formwork Frami Xlife

    Column formwork Frami Xlife

    Wall Formwork

    Frami Xlife uni­ver­sal pan­els are ide­al for forming col­umn cross-sec­tions by hand or by crane.

  • Wall formwork FF100 tec

    Wall formwork FF100 tec

    Wall Formwork

    The pre-as­sem­bled stan­dard el­e­ments of Doka timber-beam formwork FF100 tec com­bine the ad­van­tages of timber-beam formwork with the grid-re­lat­ed ad­van­tages of a framed formwork sys­tem. Their very high load-bearing ca­pac­i­ty of­fers a new de­gree of free­dom when it comes to ful­filling ar­chi­tec­tu­ral spe­c­i­fi­ca­tions in a cost-ef­fec­tive way. FF100 tec is suit­able for fair-faced con­crete cat­e­gories SB1 to SB4, as defined in the DBV Code of Prac­tice.

  • Large-area formwork Top 100 tec

    Large-area formwork Top 100 tec

    Wall Formwork

    Based on the heavy-du­ty Beam I tec 20, the new Large-area formwork Top 100 tec sys­tem is the ide­al so­lu­tion for si­t­u­a­tions re­quir­ing ab­so­lute di­men­sio­n­al ac­cu­ra­cy, de­spite high con­crete pres­sures and wide­ly spaced form-ties. The shape, size, tie-hole pat­tern and form-fac­ing of the el­e­ments can now be adapt­ed bet­ter than ev­er to suit any re­quire­ment.

  • Framed formwork Frami Eco

    Framed formwork Frami Eco

    Wall Formwork

    The lightweight Frami eco formwork, with its stur­dy pow­der-coat­ed steel frame, is ide­al for fast and eco­nom­i­cal forming, with or with­out a crane.

  • Panel floor formwork Dokadek 20

    Panel floor formwork Dokadek 20

    Floor Formwork

    Dokadek 20, the beam-less hand-set formwork with coat­ed frame and in­te­grat­ed plate sup­ports er­go­nom­ic forming. The sys­tem is de­signed for floors up to 25 cm thick and floor heights up to 3.30 m.

  • Dokaflex 30 tec

    Dokaflex 30 tec

    Floor Formwork

    Dokaflex 30 tec is a hand-set formwork sys­tem for floor-slabs that scores for its low costs-per-use. Used as a pri­mary, the high-load I tec 20 formwork beam al­lows the props to be spaced much fur­ther apart. As less equip­ment is used for the same area of formwork, the sys­tem takes 15 per­cent less time to set up, and the equip­ment and lo­gis­tics costs are al­so low­er.

  • Shaft platform

    Shaft platform

    Climbing Formwork

    The shaft platform plus shaft formwork are quick and easy to re­po­si­tion, in just one crane cy­cle.

  • Guided climbing formwork Xclimb 60

    Guided climbing formwork Xclimb 60

    Climbing Formwork

    The Guid­ed climbing formwork Xclim­b 60 is a sys­tem that is guid­ed on ver­ti­cal pro­files fixed to the struc­ture, even dur­ing re­po­si­tion­ing. The en­tire climbing unit is safe­ly and eas­i­ly re­po­si­tioned in a sin­gle crane cy­cle, even dur­ing high winds.

  • Dam formwork

    Dam formwork

    Climbing Formwork

    Dam formwork is used for forming one-sid­ed con­struc­tion pro­jects, such as dams, bar­rages, riv­er pow­er sta­tions or py­lons with­out formwork ties. The climbing tow­er will trans­fer all pour­ing loads in­to the pre­vi­ous pour­ing sec­tion. Dif­fer­ent sys­tem variants D12, D15, D22 and D35 fa­cil­i­tate eco­nom­ic adap­ta­tion to vari­ous pro­ject-spe­cif­ic block di­men­sions.

  • Cooling tower formwork SK175

    Cooling tower formwork SK175

    Climbing Formwork

    This cooling-tow­er formwork is a ful­ly mech­anised, self-climbing large-area formwork sys­tem. It max­imis­es ra­tio­n­al­i­sa­tion and min­imis­es man­u­al labour – af­ter a short fa­miliari­sa­tion pe­ri­od, the crew will soon be ac­com­plish­ing the cast­ing sec­tions in a 1-day cy­cle.

  • Climbing formwork K

    Climbing formwork K

    Climbing Formwork

    The climbing formwork sys­tem for struc­tures that need the formwork el­e­ments to be moved up in sev­er­al cast­ing sec­tions. With on­ly two accessories, the Folding plat­for­m K can be turned in­to a ful­ly func­tio­n­al crane-jumped formwork di­rect­ly on the site.

  • Climbing formwork 150F

    Climbing formwork 150F

    Climbing Formwork

    Climbing form­work 150F is a tried-and-test­ed sys­tem for crane-lift­ed climbing pro­jects. It is sim­p­ly to set up and easy to use.

  • Automatic climbing formwork SKE plus

    Automatic climbing formwork SKE plus

    Climbing Formwork

    With its mo­d­u­lar de­sign, SKE of­fers an ef­fi­cient so­lu­tion for any type of struc­ture and any re­quire­ment. The ful­ly hy­draulic equip­ment sup­ports the con­struc­tion work­flow by al­low­ing for fast and safe re­po­si­tion­ing pro­cess­es.

  • Forming wagon TU

    Forming wagon TU

    Load-bearing Systems

    With the in­no­va­tive Forming wagon TU, can­tilev­ered para­pets can be cost-ef­fi­cient­ly cast with­out dis­rupt­ing traff­ic or other con­struc­tion op­er­a­tions.

  • Forming wagon T

    Forming wagon T

    Load-bearing Systems

    Com­bined with a pre-as­sem­bled para­pet formwork that can be cy­cled with­out be­ing dis­man­tled, the trav­elling Forming wagon T is de­signed for high cost ef­fi­cien­cy.

  • Doka UniKit

    Doka UniKit

    Load-bearing Systems

    Doka UniK­it, the thor­ough­ly thought out mo­d­u­lar sys­tem for ease of pro­duc­ing shoring in spaces that re­quire ex­tra-high-ca­pac­i­ty equip­ment. It al­lows for a va­ri­e­ty of us­es where heavy loads have to be trans­ferred such as for in­fras­truc­ture and pow­er sta­tion con­struc­tion.

  • Composite forming carriage

    Composite forming carriage

    Load-bearing Systems

    The Doka composite forming car­ri­age makes for fast, safe con­struc­tion of bridges on which a con­crete deck slab is joined to a steel su­per­struc­ture. The trav­elling composite forming car­ri­age car­ries a large area of pre-as­sem­bled composite bridge-deck formwork that can be cy­cled with­out be­ing dis­man­tled. It stands out for its ex­cel­lent adapt­a­bil­i­ty to all cir­cum­s­tances, low-cost as­sem­b­ly from rentable stan­dard components, and its high work­place safe­ty.

  • Cantilever forming traveller

    Cantilever forming traveller

    Load-bearing Systems

    The Doka cantilever forming trav­eller pro­vides cer­tain­ty re­gard­ing plan­n­ing and costs while en­sur­ing an op­ti­mum con­struc­tion work­flow. The per­fect de­sign match be­tween the CFT's shoring struc­ture and the formwork, its high stan­dard of safe­ty and its op­ti­mised work­place-er­go­nom­ic de­sign to­gether en­sure that work can progress swift­ly and safe­ly.

  • Bridge formwork ParaTop

    Bridge formwork ParaTop

    Load-bearing Systems

    Doka bridge formwork Para­Top turns Large-area formwork Top 50 in­to a cantilever arm formwork that can be op­er­at­ed com­plete­ly from above. The sys­tem's in­no­va­tive insert-shoe makes it easy to erect, and com­pen­sates for any in­s­tal­la­tion in­ac­cu­ra­cy.

  • Bridge edge beam formwork T

    Bridge edge beam formwork T

    Load-bearing Systems

    Bridge edge beam formwork T is made up of a very small num­ber of dif­fer­ent parts. Its high load-bearing ca­pac­i­ty and low dead weight make it a con­vinc­ing so­lu­tion.

  • Tunnel system DokaCC

    Tunnel system DokaCC

    Load-bearing Systems

    The mo­d­u­lar Tun­nel sys­tem DokaCC is used in cut-and-cov­er con­struc­tion method to form rec­tan­gu­lar or round tun­nel cross-sec­tions quick­ly and with few­er ma­te­rials. The ap­pli­ca­bil­i­ty on all com­mon types of foun­da­tions pro­vides ad­di­tio­n­al ben­e­fit in terms of ef­fi­cien­cy.

  • Load-bearing tower d3

    Load-bearing tower d3

    Load-bearing Systems

    Load-bearing tow­er d3 scores for its high load ca­pac­i­ty, set-up speed and its broad spec­trum of ap­pli­ca­tion such as bridge-build­ing, high­rise and in­dus­trial con­struc­tion.

  • Load-bearing tower Staxo 40

    Load-bearing tower Staxo 40

    Load-bearing Systems

    The Load-bearing tow­er Stax­o 40 sys­tem stands out for be­ing ex­cep­tio­n­al­ly easy to han­dle, and su­per­b­ly adapt­able to any build­ing-con­struc­tion pro­ject.

  • Heavy-duty supporting system SL-1

    Heavy-duty supporting system SL-1

    Load-bearing Systems

    The mo­d­u­lar­ly de­signed Doka heavy-du­ty sup­port­ing sys­tem SL-1 pro­vides com­plete formwork so­lu­tions for wide­ly dif­fer­ing tun­nel cross-sec­tions, re­gard­less of shape and load.

  • Heavy-duty supporting system DokaShore

    Heavy-duty supporting system DokaShore

    Load-bearing Systems

    The Load-bearing tow­er DokaShore is used for sup­port­ing e.g. bridge su­per­struc­tures made of pre-cast con­crete mem­bers or CIP con­crete, tur­bine plat­forms and wide-spanned drive-through ac­cess open­ings, cost-ef­fec­tive­ly and safe­ly.

  • Stair tower 250

    Stair tower 250

    Safety Systems

    The stur­dy, sta­ble stair tow­er can be put to­gether very quick­ly from frames and pre-as­sem­bled stair­way el­e­ments. In­ter­me­di­ate ex­its per­mit safe ac­cess to all work-deck lev­els.

  • Platform system Xsafe plus

    Platform system Xsafe plus

    Safety Systems

    The pre-as­sem­bled, fold-out work­ing plat­forms, with their in­te­grable front/rear and side rail­ings, lad­ders and self-clos­ing man­hole lids, are ready for im­me­di­ate use and great­ly en­hance work­place safe­ty. The sys­tem can be used on Framax Xlife framed and col­umn formwork units, Framax Xlife plus and Wall formwork FF20, Top 50 and Top 100 tec.

  • Ladder system XS

    Ladder system XS

    Safety Systems

    Sys­tem-based lad­der­ways with in­te­gral lad­der cages can be at­tached to Doka wall and col­umn formwork in a few sim­ple steps. Th­ese safe­ty accessories can be mount­ed to the formwork while this is still placed flat on the ground. This en­sures com­plete safe­ty, right from the word "go".

  • Folding platform K

    Folding platform K

    Safety Systems

    Doka folding plat­forms K are pre-as­sem­bled, work-ready scaf­fold plat­forms with stan­dardised sys­tem components for all us­age si­t­u­a­tions.

  • DokaScaff


    Safety Systems

    The safe mo­d­u­lar scaf­fold for Ac­cess sys­tems as well as forming and re­in­forc­ing works

  • Bracket platform M

    Bracket platform M

    Safety Systems

    The Bracket plat­for­m M is a site-ready, lightweight work­ing and pro­tection platform that gives a big boost to safe­ty in the field of ma­son­ry and pre-cast con­struc­tion. The win­n­er of an EU award, the Bracket plat­for­m M com­plies with both EN 12811-1 (for use as a work­ing platform), and DIN 4420 (for use as a pro­tection platform).

  • Formwork return

    Formwork return


  • Formwork co-ordination

    Formwork co-ordination


  • Formwork Instructors

    Formwork Instructors


  • Execution planning

    Execution planning


  • Doka Training

    Doka Training


  • Disposal



  • Dis-assembly



  • VDC / BIM with Doka

    VDC / BIM with Doka


    Intelligent connectivity, reliable planning and significant time savings are essential benefits provided by the BIM method. We enable 3D design of formwork-related structural data in Revit and Tekla incl. export of 2D Plans and parts lists, 4D simulation of construction progress of defined work stages and much more. All the above results in less implementation planning effort due to the direct export from BIM and a maximum clarity in the subsequent process.

  • Yard Management Service

    Yard Management Service


    YMS is a transparent inventory management platform with smart interfaces towards modular selectable classical services. YMS features all position and movement data of owned and rented equipment for efficient material planning and disposition in real-time. This way YMS allows for a well-structured overview of all operating equipment at site, project and company levels.

  • Cycle planning

    Cycle planning


  • Assembly drawings

    Assembly drawings


  • 3-D-planning



  • Transport



  • Static calculations

    Static calculations


  • Reconditioning



  • Project support

    Project support


  • Project management

    Project management


  • Pre-assembly on site

    Pre-assembly on site


  • Pre-assembly



  • Safety Net Fan

    Safety Net Fan

    The ultimate debris net system for any building structure.

  • No results found. The search covers names of Doka products and services.