calldocumentfacebookmessagemypartnerwindowsapplegoogleplayworkerroutecoinspinterestplaysearchsmartphonetwittercaraccordeonvideoarrowarrowdownloaddownloaduploadsection_scrollerglobemapcontactenergyhomebridgeshighrisetunnelmininghousearrow-uparrow-downarrow-leftarrow-leftarrow-circle-rightchevron-right-circleuser
I consent to the use of cookies by this website for analyses and personalised content. Find out more OK
Back to overview

Wall formwork FF100 tec

The high-load timber-beam formwork with a sys­tem grid

The pre-as­sem­bled stan­dard el­e­ments of Doka timber-beam formwork FF100 tec com­bine the ad­van­tages of timber-beam formwork with the grid-re­lat­ed ad­van­tages of a framed formwork sys­tem. Their very high load-bearing ca­pac­i­ty of­fers a new de­gree of free­dom when it comes to ful­filling ar­chi­tec­tu­ral spe­c­i­fi­ca­tions in a cost-ef­fec­tive way. FF100 tec is suit­able for fair-faced con­crete cat­e­gories SB1 to SB4, as defined in the DBV Code of Prac­tice.

Downloads

High pour­ing rates

made pos­si­ble by ex­tra-strong components 

Up to a pour-height of 3.60 m, on­ly two 20.0 form-ties are need­ed, thanks to

  • the 80 per­cent high­er load ca­pac­i­ty of the I tec 20 composite formwork beam com­pared to con­ven­tio­n­al H20 timber formwork beams
  • the stiff FF100 tec wal­ings WU14, with their weld­ed-on plates

Max­imised util­i­sa­tion of equip­ment

and ease of han­dling 

Low­ers com­mis­sion­ing quan­ti­ties and forming-times be­cause

  • the small num­ber of el­e­ment widths, in a 25 cm grid, are sim­ple to plan
  • of the rapid avai­l­a­bil­i­ty made pos­si­ble by the sys­tem's site-ready el­e­ments with/with­out form-fac­ing
  • of the im­proved formwork el­e­ment con­nec­tors, with their op­ti­mised pull-tight and push-apart func­tion

Fair-faced con­crete formwork

made of ready-as­sem­bled stan­dard el­e­ments 

Su­perb con­crete sur­face, with no screw im­prints in the con­crete, as

  • the form-fac­ing is screwed on from the rear
  • the form-ties are lo­cat­ed well in­side the el­e­ment, in a sym­met­ri­cal pat­tern
  • the pre-as­sem­bled beam grilles mean that any type of form-fac­ing can be used
  • the in­te­gral corn­er re­in­force­ment an­gle en­sures de­pend­able seal­ing of the joint be­tween the form-ply sheets at the out­side corn­ers

Com­pre­hen­sive work­place safe­ty

with com­pat­i­ble lad­der­ways and work­ing plat­forms 

  • safe ver­ti­cal ac­cess with the Lad­der sys­tem XS
  • work­place safe­ty on all sides with the 'Platform sys­tem Xsafe plus' or with pour­ing plat­forms
  • prac­ti­cal accessories – such as pan­el struts, lift­ing/re­po­si­tion­ing de­vices etc. – make for safe, easy han­dling of the formwork

References