Wall formwork

Doka offers a wide range of proven wall formwork systems for all jobsite situations, all fields of use, and all specifications regarding the concrete finish.

  • Framed formwork Framax Xlife plus

    Framed formwork Framax Xlife plus

    Wall Formwork

    The cen­tre­piece of the new Framed formwork Framax Xlife plus is the Framax Xlife plus form tie. It can be op­er­at­ed from one side and saves up to one third in forming and strip­ping time. Due to its con­i­cal shape, there is no need for jack­et tubes and cones. In­no­va­tive: Form-tie sleeves are com­plete­ly sealed with­out wear­ing parts.

  • Framed formwork Framax Xlife

    Framed formwork Framax Xlife

    Wall Formwork

    Framax Xlife is the framed formwork sys­tem that us­es on­ly a very few dif­fer­ent pan­el for­mats to achieve a con­sis­tent 15 cm in­cre­ment-grid, no mat­ter whether the pan­els are stood up­right or on their sides. All the con­nec­tors and accessories fit seam­less­ly in­to this grid – mak­ing for fast forming-times and high ef­fi­cien­cy.

  • Large-area formwork Top 50

    Large-area formwork Top 50

    Wall Formwork

    Large-area formwork Top 50 is a 'con­struc­tion kit' large-area formwork sys­tem that is pre-as­sem­bled on a pro­ject-spe­cif­ic ba­sis and is de­signed to ac­com­plish many very di­verse types of task. The shape, size, tie-hole pat­tern and form-fac­ing of the el­e­ments can be adapt­ed to suit any re­quire­ment.

  • Column formwork Framax Xlife

    Column formwork Framax Xlife

    Wall Formwork

    Uni­ver­sal pan­els from the Framax Xlife framed-formwork range are ide­al for forming varied cross-sec­tions of col­umn in a 5 cm grid – with­out need­ing a ded­i­cat­ed col­umn formwork sys­tem on the site.

  • Framed formwork Frami Xlife

    Framed formwork Frami Xlife

    Wall Formwork

    The lightweight Frami Xlife formwork, with its stur­dy hot-dip gal­vanised steel frame, is ide­al for fast and eco­nom­i­cal forming, with or with­out a crane.

  • Dokaset


    Wall Formwork

    Dokaset is a fast, cost-sav­ing wall formwork sys­tem for the build­ing con­struc­tion seg­ment. All op­er­a­tions such as at­tach­ing the lift­ing chain and plac­ing the form-ties can be car­ried out very quick­ly and eas­i­ly from ground lev­el. Ful­ly pre-mount­ed work­ing plat­forms, the Xlife formwork sheet and wide tie spac­ing are among the prac­ti­cal fea­tures that set this all-in-one sys­tem apart.

  • Framed formwork Alu-Framax Xlife

    Framed formwork Alu-Framax Xlife

    Wall Formwork

    With its low weight, Alu-Framax Xlife brings all the ben­e­fits of Framax Xlife framed formwork to crane­less job­sites as well – al­so seam­less­ly com­bined with Framax Xlife, of course.

  • Framed formwork Frami Eco

    Framed formwork Frami Eco

    Wall Formwork

    The lightweight Frami eco formwork, with its stur­dy pow­der-coat­ed steel frame, is ide­al for fast and eco­nom­i­cal forming, with or with­out a crane.

  • Wall formwork FF100 tec

    Wall formwork FF100 tec

    Wall Formwork

    The pre-as­sem­bled stan­dard el­e­ments of Doka timber-beam formwork FF100 tec com­bine the ad­van­tages of timber-beam formwork with the grid-re­lat­ed ad­van­tages of a framed formwork sys­tem. Their very high load-bearing ca­pac­i­ty of­fers a new de­gree of free­dom when it comes to ful­filling ar­chi­tec­tu­ral spe­c­i­fi­ca­tions in a cost-ef­fec­tive way. FF100 tec is suit­able for fair-faced con­crete cat­e­gories SB1 to SB4, as defined in the DBV Code of Prac­tice.

  • Wall formwork FF20

    Wall formwork FF20

    Wall Formwork

    With its prac­ti­cal el­e­ment size-grid, rapid stack­a­bil­i­ty and slip­page-free in­ter-el­e­ment con­nec­tions, FF20 is the right choice for many pro­jects where stric­ter re­quire­ments are made re­gard­ing the con­crete fin­ish.

  • Circular formwork H20

    Circular formwork H20

    Wall Formwork

    Cir­cu­lar formwork H20 is a prac­ti­cal cir­cu­lar formwork sys­tem that de­liv­ers smooth, curved walls from radii of 3.50 m up­ward – ste­p­less­ly.

  • Facade formwork Top 50

    Facade formwork Top 50

    Wall Formwork

    Fa­cade formwork Top 50 speeds up work on pre-cast fa­cades, both with in­te­grat­ed and set-back CIP columns.

  • Large-area formwork Top 100 tec

    Large-area formwork Top 100 tec

    Wall Formwork

    Based on the heavy-du­ty Beam I tec 20, the new Large-area formwork Top 100 tec sys­tem is the ide­al so­lu­tion for si­t­u­a­tions re­quir­ing ab­so­lute di­men­sio­n­al ac­cu­ra­cy, de­spite high con­crete pres­sures and wide­ly spaced form-ties. The shape, size, tie-hole pat­tern and form-fac­ing of the el­e­ments can now be adapt­ed bet­ter than ev­er to suit any re­quire­ment.

  • Column formwork Top 50

    Column formwork Top 50

    Wall Formwork

    Com­pli­cat­ed col­umn cross-sec­tions, large col­umn heights, many formwork re-use cy­cles, tough spe­c­i­fi­ca­tions re­gard­ing the con­crete fin­ish – a made-to-mea­sure Col­umn formwork Top 50 can han­dle them all eco­nom­i­cal­ly.

  • Column formwork RS

    Column formwork RS

    Wall Formwork

    Ex­act­ly round columns, in su­perla­tive fair-faced con­crete qual­i­ty, can be achieved us­ing Col­umn formwork RS.

  • Column formwork KS Xlife

    Column formwork KS Xlife

    Wall Formwork

    For si­t­u­a­tions where large num­bers of square and rec­tan­gu­lar columns, with vari­able cross-sec­tions, need to be formed cost-ef­fec­tive­ly and on sche­d­ule.

  • Supporting construction frame AL

    Supporting construction frame AL

    Wall Formwork

    The Supporting construction frame AL is an extremely lightweight support structure for single-sided wall formwork systems that allow craneless working.

  • Supporting construction frame Universal

    Supporting construction frame Universal

    Wall Formwork

    With the supporting construction frame Universal, even high one-sided walls can be produced in one casting – for wall heights up to 12.80 m.

  • Supporting construction frame Variable

    Supporting construction frame Variable

    Wall Formwork

    The Supporting construction frame Variable is a safe and simple solution for single sided wall formwork by combining standard multi-purpose walings with add-on components - for wall heights up to 4.05 m.

  • Framini


    Wall Formwork

    The sturdy handset formwork that’s easy to use and ideal for fast, crane-independent forming.

  • DokaXlight


    Wall Formwork

    Forming made easy: At only 21.5 kg per main panel measuring 0.75 x 1.50 m, this robust handset formwork is easy to use on jobsites of any size and kind, and without the necessity of a crane. The maximum concrete pressures of 50 kN/m2 for wall formwork and 75 kN/m2 for column formwork, enables the system to be universally applicable and ideal for high pouring rates.

  • Doka Monolithic

    Doka Monolithic

    Doka Monolithic is a high-performing formwork system for casting walls and floors quickly in just one operation. Its lightweight aluminium panels and optimised forming sequence deliver greater efficiency on the site. Doka Monolithic is ideally suited for many different types of structures, including single our double storey family homes, housing developments and high-rise buildings. All components such as walls, columns, shafts, floors, beams, stairways and balconies as well as openings for windows and doors can be monolithically constructed with the system.

  • No results found. The search covers names of Doka products and services.