Solutions for your construction projects

Doka offers formwork solutions for all areas of construction activity – for anything from housing developments to transportation infrastructure and power-generation facilities, or for building the world’s tallest structures. You can choose from formwork systems and components for any construction project and any requirement.

Filter Formwork and Services
  • Framed formwork Framax Xlife

    Framed formwork Framax Xlife

    Wall Formwork

    Framax Xlife is the framed formwork sys­tem that us­es on­ly a very few dif­fer­ent pan­el for­mats to achieve a con­sis­tent 15 cm in­cre­ment-grid, no mat­ter whether the pan­els are stood up­right or on their sides. All the con­nec­tors and accessories fit seam­less­ly in­to this grid – mak­ing for fast forming-times and high ef­fi­cien­cy.

  • Panel floor formwork Dokadek 30

    Panel floor formwork Dokadek 30

    Floor Formwork

    Dokadek 30 is a beam-less, hand-set formwork sys­tem de­signed as a lightweight steel struc­ture with yel­low coat­ed frames faced with timber/plas­tic-composite sheet­ing. Dokadek 30 com­bines the ad­van­tages of a pan­el floor formwork sys­tem with those of Dokaflex floor-slab formwork: its 3 m² large pan­els make it fast in typ­i­cal zones, yet – thanks to Dokaflex – it is quick and flex­i­ble in the in­fill zones as well. Dokadek 30 – with or with­out drop head: the evo­lu­tion of floor-slab formwork.

  • Formwork beams

    Formwork beams

    System Components

    Doka timber formwork beams are the ba­sis for many Doka formwork sys­tems and have a wide range of us­es. Hun­dreds of thou­sands of th­ese care­ful­ly man­u­fac­tured beams do ster­ling ser­vice on count­less con­struc­tion sites ev­ery day. The H20 ­top and H20 e­co beams are fa­miliar names all over the world, and are the right choice for any ap­pli­ca­tion.

  • Framed formwork Frami Xlife

    Framed formwork Frami Xlife

    Wall Formwork

    The lightweight Frami Xlife formwork, with its stur­dy hot-dip gal­vanised steel frame, is ide­al for fast and eco­nom­i­cal forming, with or with­out a crane.

  • Floor props

    Floor props

    System Components

    Doka floor props are the right choice for ev­ery us­age si­t­u­a­tion, and a stur­dy 'sup­port' in the rough-and-tum­ble of ev­ery­day work on the site. The an­ti-hand­trap and an­ti-dropout safe­guard, forged nut, gal­vanised fin­ish and er­go­nom­i­cal­ly shaped fas­ten­ing clamp are just a few of the fea­tures of th­ese pre­mi­um tubu­lar steel props that have con­vinced cus­tomers all over the world.

  • Concremote


    System Components

    Mea­sur­ing the strength de­vel­op­ment of the con­crete di­rect­ly, us­ing Con­cre­mote, per­mits bet­ter ma­n­age­ment of the forming and CIP ­con­cret­ing op­er­a­tions.

  • Platform SCP

    Platform SCP

    Climbing Formwork

    The Platform SCP has room for all the site equip­ment need­ed, and is ful­ly en­closed for safe, weather-shield­ed work­ing, even at great heights. Pow­er­ful hy­draulic cylin­ders crane­less­ly raise the platform, formwork, equip­ment containers and con­crete plac­ing boom to the next cast­ing sec­tion, in on­ly one lift.

  • Large-area formwork Top 50

    Large-area formwork Top 50

    Wall Formwork

    Large-area formwork Top 50 is a 'con­struc­tion kit' large-area formwork sys­tem that is pre-as­sem­bled on a pro­ject-spe­cif­ic ba­sis and is de­signed to ac­com­plish many very di­verse types of task. The shape, size, tie-hole pat­tern and form-fac­ing of the el­e­ments can be adapt­ed to suit any re­quire­ment.

  • Framed formwork Framax Xlife plus

    Framed formwork Framax Xlife plus

    Wall Formwork

    The cen­tre­piece of the new Framed formwork Framax Xlife plus is the Framax Xlife plus form tie. It can be op­er­at­ed from one side and saves up to one third in forming and strip­ping time. Due to its con­i­cal shape, there is no need for jack­et tubes and cones. In­no­va­tive: Form-tie sleeves are com­plete­ly sealed with­out wear­ing parts.

  • Dokamatic table

    Dokamatic table

    Floor Formwork

    The in­no­va­tive­ly de­signed Dokamatic table is the fast way to form large ar­eas of slab. The sys­tem is op­ti­mised to give short forming-times, and copes well with vary­ing struc­tu­ral-de­sign and ge­o­met­ri­cal re­quire­ments. Save on man­hours and crane time: with the 'DoKart plus', the ta­bles can eas­i­ly be trav­elled to their next lo­ca­tion by just one man work­ing on his own.

  • DFDS Formwork Planning

    DFDS Formwork Planning


  • Protection screen Xclimb 60

    Protection screen Xclimb 60

    Safety Systems

    The Pro­tection screen Xclimb 60 lets you car­ry out con­struc­tion work in the top build­ing-lev­els of high-rise pro­jects in great safe­ty, and pro­tect­ed from the weather. Pro­tection screen Xclimb 60 is a hy­drauli­cal­ly climbed sys­tem that can al­so be quick­ly re­po­si­tioned by crane if suf­fi­cient craneage is avai­l­able. Be­cause it is struc­ture-guid­ed at all times, it can be op­er­at­ed even in windy con­di­tions. The sys­tem comes in sev­er­al ver­sions, giv­ing you the ide­al so­lu­tion for ev­ery re­quire­ment.

  • myDoka customer portal

    myDoka customer portal


  • Load-bearing tower Staxo 100

    Load-bearing tower Staxo 100

    Load-bearing Systems

    With its rugged steel frames, Staxo 100 is de­signed for large shoring-heights and high loads. It unites high load ca­pac­i­ty and safe­ty, in ev­ery si­t­u­a­tion.

  • Wall formwork FF20

    Wall formwork FF20

    Wall Formwork

    With its prac­ti­cal el­e­ment size-grid, rapid stack­a­bil­i­ty and slip­page-free in­ter-el­e­ment con­nec­tions, FF20 is the right choice for many pro­jects where stric­ter re­quire­ments are made re­gard­ing the con­crete fin­ish.

  • Climbing formwork MF240

    Climbing formwork MF240

    Climbing Formwork

    Climbing formwork MF240 per­mits con­trolled, reg­u­lar work­ing cy­cles on all struc­tures. The sys­tem is sim­ple to op­er­ate, han­dles wall in­cli­na­tions of up to 15 de­grees and can be di­men­sioned to many dif­fer­ent re­quire­ments over a wide range of ap­pli­ca­tions.

  • Supporting construction frame

    Supporting construction frame

    Wall Formwork

    'Sup­port­ing con­struc­tion frames' en­able the con­cret­ing forces to be safe­ly trans­ferred by way of di­ag­o­n­al an­chors in cas­es where it is not pos­si­ble to tie wall-formwork el­e­ments through the con­crete.

  • Circular formwork H20

    Circular formwork H20

    Wall Formwork

    Cir­cu­lar formwork H20 is a prac­ti­cal cir­cu­lar formwork sys­tem that de­liv­ers smooth, curved walls from radii of 3.50 m up­ward – ste­p­less­ly.

  • Edge protection system XP

    Edge protection system XP

    Safety Systems

    This sys­tem is the uni­ver­sal safe­ty so­lu­tion for all edge pro­tection needs. It fits in ide­al­ly with Doka sys­tems – be they wall or floor-slab formwork – for safe­guard­ing slab-edges or as fall-ar­rest bar­ri­ers on the struc­ture shell.

  • Plumbing accessories

    Plumbing accessories

    System Components

    Doka pan­el struts and plumb­ing struts wind­proof the formwork and make it easi­er to plumb and align. The mo­d­u­lar com­bi­na­tion of plumb­ing struts, prop heads and prop shoes makes for op­ti­mum us­a­bil­i­ty with Doka formwork sys­tems.

  • Framed formwork Alu-Framax Xlife

    Framed formwork Alu-Framax Xlife

    Wall Formwork

    With its low weight, Alu-Framax Xlife brings all the ben­e­fits of Framax Xlife framed formwork to crane­less job­sites as well – al­so seam­less­ly com­bined with Framax Xlife, of course.

  • Dokaflex


    Floor Formwork

    Dokaflex is the timber-beam floor formwork for all kinds of lay­outs. Meet­ing in­di­vi­d­u­al re­quire­ments re­gard­ing the con­crete fin­ish is no problem, as any type of form-fac­ing can be cho­sen. Two Dokaflex de­sign ver­sions are avai­l­able for use to meet your pro­ject re­quire­ments.

  • 3-ply sheets, formwork sheets

    3-ply sheets, formwork sheets

    System Components

    Doka 3-SO three-ply sheets pro­vide the ba­sis for many Doka formwork sys­tems and have a wide range of us­es.

  • Multi-ply formwork sheets

    Multi-ply formwork sheets

    System Components

    Doka mul­ti-ply formwork sheets are used in very many Doka formwork sys­tems. The broad spec­trum – rang­ing from Doka­P­ly to the Xlife sheet – al­lows Doka to of­fer ide­al so­lu­tions for many dif­fer­ent re­quire­ments and cater for any­thing from in­fill zones to fair-faced con­crete.

  • Automatic climbing formwork Xclimb 60

    Automatic climbing formwork Xclimb 60

    Climbing Formwork

    Au­to­mat­ic climbing formwork Xclim­b 60 is a hy­drauli­cal­ly climbed sys­tem that can al­so be quick­ly raised by crane if suf­fi­cient craneage is avai­l­able. Be­cause it is guid­ed on the struc­ture at all times, the sys­tem can still be climbed even in windy con­di­tions.

  • Shifting devices for tables

    Shifting devices for tables

    Floor Formwork

    With Doka shift­ing de­vices, slab-forming op­er­a­tions can be ac­com­plished even faster. By mak­ing the crane un­ne­ces­sary for both the hor­i­zon­tal and ver­ti­cal re­po­si­tion­ing op­er­a­tions, they sim­pli­fy and op­ti­mise the lo­gis­tics for the en­tire site, by do­ing away with un­pro­duc­tive (mean­ing cost­ly) wait­ing times. The craneage saved here is then avai­l­able for use else­where. This ac­cel­er­ates the en­tire site work­flow, sav­ing on labour costs and boost­ing the con­trac­tors' com­pet­i­tive­ness.

  • Working scaffold Modul

    Working scaffold Modul

    Safety Systems

    The Work­ing scaf­fold Mo­d­ul is the ide­al add-on to Doka wall sys­tems: with this rentable mo­d­u­lar platform sys­tem, re­in­force­ment op­er­a­tions can be car­ried out safe­ly and quick­ly. It is equal­ly suit­able for use as a stair tow­er or a mo­bile scaf­fold tow­er. To speed up the con­struc­tion work­flow still fur­ther, the platform units can be re­po­si­tioned by crane.

  • Dokaflex table

    Dokaflex table

    Floor Formwork

    Dokaflex ta­bles are easy and prac­ti­cal to set up and can be shift­ed and adapt­ed very quick­ly. This makes them a cost-ef­fec­tive and ef­fi­cient way of car­ry­ing out large-area slab pro­jects. Dokaflex ta­bles can of course be com­bined with Dokamatic ta­bles.

  • Release-agents


    System Components

    Doka of­fers re­lease-agents for both smooth and ab­sor­bent formwork sur­faces. They have an ex­cel­lent se­parat­ing ef­fect and make for at­trac­tive con­crete sur­faces.

  • Multi-trip packaging

    Multi-trip packaging

    System Components

    Mul­ti-trip pack­ag­ing items such as containers, stack­ing pallets and skele­ton tran­s­port box­es keep ev­ery­thing neat and tidy on the site, min­imise the time wast­ed search­ing for parts and stream­line the stor­age and tran­s­port of sys­tem components, small items and accessories. The stack­ing pallets sim­pli­fy the stor­age and han­dling of floor props, folding tripods, formwork beams and sheets. The skele­ton tran­s­port box is the tidy way of stor­ing and han­dling lighter accessories (max. load 700 kg). For heavi­er accessories, there is plen­ty of space for th­ese in the Mul­ti-trip tran­s­port box (max. load 1500 kg).

  • Form ties/Suspension cones

    Form ties/Suspension cones

    System Components

    De­pend­able form-ties and safe sus­pen­sion points are cru­cial for ef­fi­cient and safe us­age of any formwork. For both wall formwork, sin­gle-sid­ed formwork and climbing formwork, a com­plete range of field-proven form-tie so­lu­tions and sus­pen­sion points is avai­l­able.

  • Aluminium formwork beams

    Aluminium formwork beams

    System Components

    The in­no­va­tive cross-sec­tion of the Alu box beam gives it a high load rat­ing, per­mitt­ing op­ti­mised equip­ment us­age on the site. The in­te­grat­ed nail­ing strip and the end-to-end fix­ing slot en­able the beam to be re-used in­ten­sive­ly, and give it a long lifes­pan.

  • Facade formwork Top 50

    Facade formwork Top 50

    Wall Formwork

    Fa­cade formwork Top 50 speeds up work on pre-cast fa­cades, both with in­te­grat­ed and set-back CIP columns.

  • Dokaset


    Wall Formwork

    Dokaset is a fast, cost-sav­ing wall formwork sys­tem for the build­ing con­struc­tion seg­ment. All op­er­a­tions such as at­tach­ing the lift­ing chain and plac­ing the form-ties can be car­ried out very quick­ly and eas­i­ly from ground lev­el. Ful­ly pre-mount­ed work­ing plat­forms, the Xlife formwork sheet and wide tie spac­ing are among the prac­ti­cal fea­tures that set this all-in-one sys­tem apart.

  • Column formwork Top 50

    Column formwork Top 50

    Wall Formwork

    Com­pli­cat­ed col­umn cross-sec­tions, large col­umn heights, many formwork re-use cy­cles, tough spe­c­i­fi­ca­tions re­gard­ing the con­crete fin­ish – a made-to-mea­sure Col­umn formwork Top 50 can han­dle them all eco­nom­i­cal­ly.

  • Column formwork RS

    Column formwork RS

    Wall Formwork

    Ex­act­ly round columns, in su­perla­tive fair-faced con­crete qual­i­ty, can be achieved us­ing Col­umn formwork RS.

  • Column formwork KS Xlife

    Column formwork KS Xlife

    Wall Formwork

    For si­t­u­a­tions where large num­bers of square and rec­tan­gu­lar columns, with vari­able cross-sec­tions, need to be formed cost-ef­fec­tive­ly and on sche­d­ule.

  • Column formwork Frami Xlife

    Column formwork Frami Xlife

    Wall Formwork

    Frami Xlife uni­ver­sal pan­els are ide­al for forming col­umn cross-sec­tions by hand or by crane.

  • Wall formwork FF100 tec

    Wall formwork FF100 tec

    Wall Formwork

    The pre-as­sem­bled stan­dard el­e­ments of Doka timber-beam formwork FF100 tec com­bine the ad­van­tages of timber-beam formwork with the grid-re­lat­ed ad­van­tages of a framed formwork sys­tem. Their very high load-bearing ca­pac­i­ty of­fers a new de­gree of free­dom when it comes to ful­filling ar­chi­tec­tu­ral spe­c­i­fi­ca­tions in a cost-ef­fec­tive way. FF100 tec is suit­able for fair-faced con­crete cat­e­gories SB1 to SB4, as defined in the DBV Code of Prac­tice.

  • Large-area formwork Top 100 tec

    Large-area formwork Top 100 tec

    Wall Formwork

    Based on the heavy-du­ty Beam I tec 20, the new Large-area formwork Top 100 tec sys­tem is the ide­al so­lu­tion for si­t­u­a­tions re­quir­ing ab­so­lute di­men­sio­n­al ac­cu­ra­cy, de­spite high con­crete pres­sures and wide­ly spaced form-ties. The shape, size, tie-hole pat­tern and form-fac­ing of the el­e­ments can now be adapt­ed bet­ter than ev­er to suit any re­quire­ment.

  • Framed formwork Frami Eco

    Framed formwork Frami Eco

    Wall Formwork

    The lightweight Frami eco formwork, with its stur­dy pow­der-coat­ed steel frame, is ide­al for fast and eco­nom­i­cal forming, with or with­out a crane.

  • Panel floor formwork Dokadek 20

    Panel floor formwork Dokadek 20

    Floor Formwork

    Dokadek 20, the beam-less hand-set formwork with coat­ed frame and in­te­grat­ed plate sup­ports er­go­nom­ic forming. The sys­tem is de­signed for floors up to 25 cm thick and floor heights up to 3.30 m.

  • Dokaflex 30 tec

    Dokaflex 30 tec

    Floor Formwork

    Dokaflex 30 tec is a hand-set formwork sys­tem for floor-slabs that scores for its low costs-per-use. Used as a pri­mary, the high-load I tec 20 formwork beam al­lows the props to be spaced much fur­ther apart. As less equip­ment is used for the same area of formwork, the sys­tem takes 15 per­cent less time to set up, and the equip­ment and lo­gis­tics costs are al­so low­er.

  • Shaft platform

    Shaft platform

    Climbing Formwork

    The shaft platform plus shaft formwork are quick and easy to re­po­si­tion, in just one crane cy­cle.

  • Guided climbing formwork Xclimb 60

    Guided climbing formwork Xclimb 60

    Climbing Formwork

    The Guid­ed climbing formwork Xclim­b 60 is a sys­tem that is guid­ed on ver­ti­cal pro­files fixed to the struc­ture, even dur­ing re­po­si­tion­ing. The en­tire climbing unit is safe­ly and eas­i­ly re­po­si­tioned in a sin­gle crane cy­cle, even dur­ing high winds.

  • Dam formwork

    Dam formwork

    Climbing Formwork

    Dam formwork is used for forming one-sid­ed con­struc­tion pro­jects, such as dams, bar­rages, riv­er pow­er sta­tions or py­lons with­out formwork ties. The climbing tow­er will trans­fer all pour­ing loads in­to the pre­vi­ous pour­ing sec­tion. Dif­fer­ent sys­tem variants D12, D15, D22 and D35 fa­cil­i­tate eco­nom­ic adap­ta­tion to vari­ous pro­ject-spe­cif­ic block di­men­sions.

  • Cooling tower formwork SK175

    Cooling tower formwork SK175

    Climbing Formwork

    This cooling-tow­er formwork is a ful­ly mech­anised, self-climbing large-area formwork sys­tem. It max­imis­es ra­tio­n­al­i­sa­tion and min­imis­es man­u­al labour – af­ter a short fa­miliari­sa­tion pe­ri­od, the crew will soon be ac­com­plish­ing the cast­ing sec­tions in a 1-day cy­cle.

  • Climbing formwork K

    Climbing formwork K

    Climbing Formwork

    The climbing formwork sys­tem for struc­tures that need the formwork el­e­ments to be moved up in sev­er­al cast­ing sec­tions. With on­ly two accessories, the Folding plat­for­m K can be turned in­to a ful­ly func­tio­n­al crane-jumped formwork di­rect­ly on the site.

  • Climbing formwork 150F

    Climbing formwork 150F

    Climbing Formwork

    Climbing form­work 150F is a tried-and-test­ed sys­tem for crane-lift­ed climbing pro­jects. It is sim­p­ly to set up and easy to use.

  • Automatic climbing formwork SKE plus

    Automatic climbing formwork SKE plus

    Climbing Formwork

    With its mo­d­u­lar de­sign, SKE of­fers an ef­fi­cient so­lu­tion for any type of struc­ture and any re­quire­ment. The ful­ly hy­draulic equip­ment sup­ports the con­struc­tion work­flow by al­low­ing for fast and safe re­po­si­tion­ing pro­cess­es.

  • Forming wagon TU

    Forming wagon TU

    Load-bearing Systems

    With the in­no­va­tive Forming wagon TU, can­tilev­ered para­pets can be cost-ef­fi­cient­ly cast with­out dis­rupt­ing traff­ic or other con­struc­tion op­er­a­tions.

  • Forming wagon T

    Forming wagon T

    Load-bearing Systems

    Com­bined with a pre-as­sem­bled para­pet formwork that can be cy­cled with­out be­ing dis­man­tled, the trav­elling Forming wagon T is de­signed for high cost ef­fi­cien­cy.

  • Doka UniKit

    Doka UniKit

    Load-bearing Systems

    Doka UniK­it, the thor­ough­ly thought out mo­d­u­lar sys­tem for ease of pro­duc­ing shoring in spaces that re­quire ex­tra-high-ca­pac­i­ty equip­ment. It al­lows for a va­ri­e­ty of us­es where heavy loads have to be trans­ferred such as for in­fras­truc­ture and pow­er sta­tion con­struc­tion.

  • Composite forming carriage

    Composite forming carriage

    Load-bearing Systems

    The Doka composite forming car­ri­age makes for fast, safe con­struc­tion of bridges on which a con­crete deck slab is joined to a steel su­per­struc­ture. The trav­elling composite forming car­ri­age car­ries a large area of pre-as­sem­bled composite bridge-deck formwork that can be cy­cled with­out be­ing dis­man­tled. It stands out for its ex­cel­lent adapt­a­bil­i­ty to all cir­cum­s­tances, low-cost as­sem­b­ly from rentable stan­dard components, and its high work­place safe­ty.

  • Cantilever forming traveller

    Cantilever forming traveller

    Load-bearing Systems

    The Doka cantilever forming trav­eller pro­vides cer­tain­ty re­gard­ing plan­n­ing and costs while en­sur­ing an op­ti­mum con­struc­tion work­flow. The per­fect de­sign match be­tween the CFT's shoring struc­ture and the formwork, its high stan­dard of safe­ty and its op­ti­mised work­place-er­go­nom­ic de­sign to­gether en­sure that work can progress swift­ly and safe­ly.

  • Bridge formwork ParaTop

    Bridge formwork ParaTop

    Load-bearing Systems

    Doka bridge formwork Para­Top turns Large-area formwork Top 50 in­to a cantilever arm formwork that can be op­er­at­ed com­plete­ly from above. The sys­tem's in­no­va­tive insert-shoe makes it easy to erect, and com­pen­sates for any in­s­tal­la­tion in­ac­cu­ra­cy.

  • Bridge edge beam formwork T

    Bridge edge beam formwork T

    Load-bearing Systems

    Bridge edge beam formwork T is made up of a very small num­ber of dif­fer­ent parts. Its high load-bearing ca­pac­i­ty and low dead weight make it a con­vinc­ing so­lu­tion.

  • Tunnel system DokaCC

    Tunnel system DokaCC

    Load-bearing Systems

    The mo­d­u­lar Tun­nel sys­tem DokaCC is used in cut-and-cov­er con­struc­tion method to form rec­tan­gu­lar or round tun­nel cross-sec­tions quick­ly and with few­er ma­te­rials. The ap­pli­ca­bil­i­ty on all com­mon types of foun­da­tions pro­vides ad­di­tio­n­al ben­e­fit in terms of ef­fi­cien­cy.

  • Load-bearing tower d3

    Load-bearing tower d3

    Load-bearing Systems

    Load-bearing tow­er d3 scores for its high load ca­pac­i­ty, set-up speed and its broad spec­trum of ap­pli­ca­tion such as bridge-build­ing, high­rise and in­dus­trial con­struc­tion.

  • Load-bearing tower Staxo 40

    Load-bearing tower Staxo 40

    Load-bearing Systems

    The Load-bearing tow­er Stax­o 40 sys­tem stands out for be­ing ex­cep­tio­n­al­ly easy to han­dle, and su­per­b­ly adapt­able to any build­ing-con­struc­tion pro­ject.

  • Heavy-duty supporting system SL-1

    Heavy-duty supporting system SL-1

    Load-bearing Systems

    The mo­d­u­lar­ly de­signed Doka heavy-du­ty sup­port­ing sys­tem SL-1 pro­vides com­plete formwork so­lu­tions for wide­ly dif­fer­ing tun­nel cross-sec­tions, re­gard­less of shape and load.

  • Heavy-duty supporting system DokaShore

    Heavy-duty supporting system DokaShore

    Load-bearing Systems

    The Load-bearing tow­er DokaShore is used for sup­port­ing e.g. bridge su­per­struc­tures made of pre-cast con­crete mem­bers or CIP con­crete, tur­bine plat­forms and wide-spanned drive-through ac­cess open­ings, cost-ef­fec­tive­ly and safe­ly.

  • Stair tower 250

    Stair tower 250

    Safety Systems

    The stur­dy, sta­ble stair tow­er can be put to­gether very quick­ly from frames and pre-as­sem­bled stair­way el­e­ments. In­ter­me­di­ate ex­its per­mit safe ac­cess to all work-deck lev­els.

  • Platform system Xsafe plus

    Platform system Xsafe plus

    Safety Systems

    The pre-as­sem­bled, fold-out work­ing plat­forms, with their in­te­grable front/rear and side rail­ings, lad­ders and self-clos­ing man­hole lids, are ready for im­me­di­ate use and great­ly en­hance work­place safe­ty. The sys­tem can be used on Framax Xlife framed and col­umn formwork units, Framax Xlife plus and Wall formwork FF20, Top 50 and Top 100 tec.

  • Ladder system XS

    Ladder system XS

    Safety Systems

    Sys­tem-based lad­der­ways with in­te­gral lad­der cages can be at­tached to Doka wall and col­umn formwork in a few sim­ple steps. Th­ese safe­ty accessories can be mount­ed to the formwork while this is still placed flat on the ground. This en­sures com­plete safe­ty, right from the word "go".

  • Folding platform K

    Folding platform K

    Safety Systems

    Doka folding plat­forms K are pre-as­sem­bled, work-ready scaf­fold plat­forms with stan­dardised sys­tem components for all us­age si­t­u­a­tions.

  • DokaScaff


    Safety Systems

    The safe mo­d­u­lar scaf­fold for Ac­cess sys­tems as well as forming and re­in­forc­ing works

  • Bracket platform M

    Bracket platform M

    Safety Systems

    The Bracket plat­for­m M is a site-ready, lightweight work­ing and pro­tection platform that gives a big boost to safe­ty in the field of ma­son­ry and pre-cast con­struc­tion. The win­n­er of an EU award, the Bracket plat­for­m M com­plies with both EN 12811-1 (for use as a work­ing platform), and DIN 4420 (for use as a pro­tection platform).

  • Formwork return

    Formwork return


  • Formwork co-ordination

    Formwork co-ordination


  • Formwork Instructors

    Formwork Instructors


  • Execution planning

    Execution planning


  • VDC / BIM with Doka

    VDC / BIM with Doka


    Integrated formwork concepts on your virtual site, boosting productivity on your real site

  • Yard management

    Yard management


  • Assembly drawings

    Assembly drawings


  • Static calculations

    Static calculations


  • Project support

    Project support


  • Project management

    Project management


  • Pre-assembly on site

    Pre-assembly on site


  • Safety Net Fan

    Safety Net Fan

    The ultimate debris net system for any building structure.

  • No results found. The search covers names of Doka products and services.